How to Modify your Hex Keys to Decimal ...

To change / update the Hex Keys to Decimal in your MR Cam
use the converter below....
Just add the Hex Keys you wish to
update at two bytes at a time, and then click
convert, copy the results found under Decimal and
enter the results in the correct option of your MR.
When updating your key you will see it asks
for 3 keys _ _ _ if any of your conversions result in a
two key conversion add a 0 first: so if the result of a
conversion was 53 you must enter it as 053 in the MR.

Example of conversion:
Enter Hex Key as 8 seperate 2 byte keys to avoid errors.
Hex Key:   D2     F2      76      42      3D     AF     AD      8D
Decimal:  210    242    118     066    061    175    173     141

Press 'OK' after each sets of 3 Decimal Keys you enter in the Joker Cam

The above application to be used to convert Hex Keys into MR Keys, just enter the Hex Key and convert into Decimal, then enter the Decimal Key into your Matrix Cam via the Remote Control.

Misc Software

****** DONīT USE THE MATRIX REVOLUTIONS FIRMWARE ON ANY OTHER CAMS ******

Matrix Revolutions

Download	MRv v3.16 D+ fix 27 sept
Download	MRv Funcard Flash File
Download	MRv v2.25 Bin for Cas Interface Use
Download	Matrix Revolutions v2.25 Fun6
Download	Matrix Revolutions v2.25 Fun5
Download	MRv v2.23 Bin for Cas Interface Use
Download	MRv v2.22 Bin for Cas Interface Use
Download	Matrix Revolutions v2.22 Fun6
Download	Matrix Revolutions v2.22 Fun5
Download	MRv v2.21 Bin for Cas Interface Use
Download	Matrix Revolutions v2.21 Fun6
Download	Matrix Revolutions v2.21 Fun5
Download	MRv v2.20 Bin for Cas Interface Use
Download	Matrix Revolutions v2.20 Fun6
Download	Matrix Revolutions v2.20 Fun5
Download	MRv v2.19 Bin for Cas Interface Use
Download	Matrix Revolutions v2.19 Fun6
Download	Matrix Revolutions v2.19 Fun5
Download	MRv v2.18 Bin for Cas Interface Use
Download	Matrix Revolutions v2.18 Fun6
Download	Matrix Revolutions v2.18 Fun5

****** DONīT USE THE MATRIX REVOLUTIONS FIRMWARE ON ANY OTHER CAMS ******

Matrix Reloaded

****** DONīT USE THE MATRIX RELOADED FIRMWARE ON ANY OTHER CAMS ******

****** DONīT USE THE MATRIX RELOADED FIRMWARE ON ANY OTHER CAMS ******

Smart Card download procedure:

1.- Select Ci menu->UCAS V3.0->Download
2.- The messages "Erasing old data, please wait..." and "Insert card 1 or serial
dummy card" will be shown.
3.- Insert the first smart card and press Ok.
4.- The message "Card inserted, opening" is shown, and then
"Performing smart card download..."
5.- If several cards are used, the message "Download card completed.
Please, extract it" will appear after the first smart card has been downloaded.
Extract the Smart Card and press Ok. After that, the message
"Insert card 2" will be shown.
6.- Insert the next smart card and press Ok.
7.- After the last smart card is downloaded, the message "Download complete.
Copying image and re-booting" will be shown. If the new version of software
is not shown after 30 seconds, re-insert the module without any smartcard.
If, after re-inserting the module, it is not initialised, switch the STB Off and
On again with the module inserted.

Notes:
1.- If you experience any problem before starting the downloading, the  message
"invalid card" is shown make sure you are inserting the cards in the correct order,
check that the first card is card one.Insert card one again and press ok.
You can also try inserting the module with the correct smart card already
inserted in the cam. In this instance, you don't need to press Ok.

2.- If the smartcard is extracted or it does not respond, a message will be
shown. Press Ok, and the next menu will be shown:
- Go on with current download
- Start a new download.
Select "Go on" in order to continue with the current smart card...
or select Start a new download to start with the first smart card
Then follow the instructions.
If you extract the module while a downloading is performed, you can continue
with the current smart card in the same way because this same menu will be
shown after selecting the downloading menu.

Serial download procedure:
Version 1.3 of Windows Downloading application must be used.
1.- Insert CAM with dummy card already inserted. After a while, a message
"This card is not valid for your..." will be shown. Press Ok.
2.- Select CI menu->UCAS V3.0->Download
3.- The messages "Erasing old data, please wait..." and "Insert card 1 or serial
dummy card" will be shown.
4.- The message "Card inserted. Openning" will appear. Then, as soon as
"Performing serial download" is shown, press "Download now" in the
Windows Downloading Application.
After a while, the message "Download complete. Copying image and re-booting" will be shown.
If the new version of software is not shown after 30 seconds,
re-insert the module without dummy card.
If, after re-inserting the module, it is not initialised, switch the STB Off and
On again with the module inserted.

Laptop download procedure:
Version 1.3 of Windows Downloading application must be used.
The procedure is exactly the same than the used in previous versions of UCAS.

****** DONīT USE THE MATRIX RELOADED FIRMWARE ON ANY OTHER CAMS ******